Activity in Technology and Support
UCCX CUIC - SMTP From address for e mailed reports
Where does one set the FROM e mail address used by CUIC report scheduler to e mail reports? I thought I knew....but it isn't where I thought it was. And I cannot find it in any documentation....
Cisco Hyperflex cluster installation failed
Hi All, My hyperflex cluster failed with the error "configure Service profile(SP) failed" "Associating Service Profile" during the UCSM configuration in each server but validation was successful. I have 6 nos of hyperflex UCS 240 m5 all-flash nodes a...
Best Ceramic Coating Services in Penang
Restore and protect your car's glossy finish with Ceramic Coating services by World Tech Sdn Bhd in Penang! Our advanced ceramic coating formulas provide durable protection against scratches, UV rays, and environmental contaminants, while enhancing t...
wireless authentication
hello I am working in an environment where there is a wireless guest infrastructure configured guest users are given access by an Administrator based on their email there is a requirement for a wireless printer to be given access to this guest net...
IPSEC VPN
Hello Team,I have below topology : -I have ipsec vpn from on-prem to aws cloud. the two endpoints [192.168.40.10/32, 192.168.30.10/32] work fine as they are allowed on the encryption domain.I have users using remote vpn to connect to on-prem dc to a...
ISE CoA Reauth for Aruba 2530
Hello everyone, Does anyone know the attributes to configure to make the CoA type reauth work on an Aruba 2530 switch (16.11)? I managed to make the CoA Disconnect and port bounce working but I don't have the solution for reauth and I need it for pro...
Catalyst center backups
HiCan I jusy clarify some backup information please? The automation only backup is what you would restore if your cluster went awol and you are recovering all your fabric info? Device configs, hand offs, port allocations, L2/L3 VN info, SGT matrix ...
IOS-XRv 9000 unreachable from non-local network
I have a IOS-XRv 9000 with SSH and gRPC enabled, running on the latest version of CML. gRPC is not working from a remote network?
copy xmodem initializing no transfer c2960
Hi Guys, i had this problem for 8 hours now and can't seem to get it cracked... after i input the command copy xmodem: flash:c2960-lanbasek9-mz.152-7.e9.binand using the SecureCRT going to Transfer > send xmodem I get this and after that nothing happ...
ACI multipod with vPC HA FW
Hi All, I need your assistance to check if the following configuration going to work and are there any drawbacks/caveats?So far I identified OSPF convergence time and impact on a relatively large area 0 *(legacy design). Solution details:I have ACI M...
The operation took longer than expected.
I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...
Router LTE connection breaks down
HelloFor a short time now, my LTE connection in the Cisco router has been breaking down repeatedly. This is very annoying because the VPN tunnel used is always gone. Unfortunately I can't do much with the logging messages. these messages are shown af...
Expressway Single Domain 2 Seperate Expressways
Hi,We have a customer using HCS. As part of this we set up Expressway for them during the first lockdown for them to be able to use Jabber remotely for voice only (no IM&P). They use the same domain name internally and externally e.g. abc.com Another...
CISCO WSA upgrade alert error
We have upgraded our S1000v(wsa ) from 14.5.1 to 14.5.2 and upgrade was successful but when we checked the alerts we found an alerts as An application fault occurred: ('heimdall/svc.py send_command|195', "<class 'heimdall.exceptions.unknownprocess'="...
CMX - cmxadmin password recovery 11.0
I am following this document to recover and reset the password for "cmxadmin" https://www.cisco.com/c/en/us/td/docs/wireless/mse/11-0-1/cmx-config/b_cg_cmx1101/performing_administrative_tasks.html#id_131101 When I reset my VM Server and edit ("e") in...
| User | Helpful Count |
|---|---|
| 112 | |
| 111 | |
| 86 | |
| 64 | |
| 63 |
