Activity in Technology and Support
Puzzling results when pasting in ACL config to switch
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
slow data transfer rate between vlans using pbr
hii have cisco 6500 series core switch and facing a bizarre issue with data speed transfer.I have two vlans svi for which is defined on this switch (core6500). these vlans are transported to another switch (sw5) via lacp etherchannel which is providi...
Can I change the regulatory domain for our new CW9164I-ROW AP?
We have a 9800-CL Wireless Controller running 17.12.2. We just got a new CW9164I-ROW AP and its registered by the operational interfaces are down due to a regulatory domain error. Is there a way to change the regulatory domain for the access point?...
Dumping CUCM Fresh Install Logs - Virtualization
IntroductionProblem DescriptionProcedureNote IntroductionThis document covers the Procedure for Dumping CUCM Fresh Install Logs - Virtualization Problem DescriptionIn order to dump install logs on a virtual UC installation, it is necessary to use a ...
Wireless IOSxe Client Ioslation and multicast
Hey everyone,Questions - on a guest WLAN I have client isolation enabled via the Peer to Peer blocking action to drop. I can see it blocks peer to peer unicast traffic, however multicast traffic between peers still flows. I can limit the mdns messa...
Multi san callmanger certificate private key distribution
Hello, Apologies for how late this question is! I have read that it is possible to generate a multi san certificate for the call manager service. Each subscriber in the cluster then uses the same certificate for call manager service. If I generate a...
Problems with SNMP on the ASA 5555-X
Hello everyone,I have a CISCO ASA 5555-X configured in multi-context mode and I want to monitor it via SNMP.However, I can't find the MIB files for this device.How can I get them?I don't have access to ftp://ftp.cisco.com/pub/mibs/supportlists/asa/as...
Secure Client 5.1.1.42 with NAM and tethering to iPhone iOS 17.2.1
We have tried upgrading from Cisco AnyConnect 4.10.07073 to Secure Client 5.1.1.42 with NAM connecting to wired and wireless networks.After the upgrade NAM fails to acquire the IP address from the phone.Connecting to enterprise EAP SSIDs and other us...
confusion over route selected from routing table
Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?People are saying that the answer ...
Installing Secure Client (5.x) AND Any Connect (4.x) on 1 computer
I have a weird situation I need to connect to two sepaate VPN (not at the same time).One of these requires Cisco Secure Client 5.x the second works with Any Connect 4.x.I have Cisco Secure Client 5.x installed, if i try connecting to the VPN that use...
Unable to ping between two tunnel points
Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...
Access Points show 0 clients
DNAC Installed Version: 2.3.5.5-70026Cisco Catalyst 9800-80 17.9.4aAXE 9120i, 9130We have about 10 employees in our office using DNAC at varying role assignment levels.I am Super-Administrator and handle most of the the WIFI related tasks. Of all the...
problem accessing the sntc portal
i cannot log in to the SNTC portal, i have the necessary roles applied last Monday (beyond the 24 hour period that is required for SNTC portal access), but each time i try to log in at services.cisco.com, I'm redirected back to the registration page ...
anyconnect WSL 2 - Windows Substem for Linux
After starting anyconnect I find network connectivity stops working under WSL2 (Windows Substem for Linux)the fix seems to be: Get-NetAdapter | Where-Object {$_.InterfaceDescription -Match "Cisco AnyConnect"} | Set-NetIPInterface -InterfaceMetric 400...
Creating public space with restrictions
Hi, I would like to create a public space where the members/admins can chat and they are the only ones who can see it and all the others can post and they can see the answers only. I do not know whether it is possible or not. Any thoughts welcome.Tha...
| User | Helpful Count |
|---|---|
| 103 | |
| 79 | |
| 78 | |
| 64 | |
| 58 |
