Technology and Support

Why Cisco ISE ping Server domain name (SRV.local) ?

I did not join my Cisco ISE in the Active Directory DNS zone, but the Cisco ISE still could resolve the domain name of the server which is SRV.local and could ping test.SRV.local, shall i still need to put it in the DNS zone and in the Reversed DNS Z...

Trunking an ip addressed inside interface on Firepower 2130

My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...

Answer phone

I have headset Bluetooth paired with cisco phones and working fine, but auto answer not work. I tried to enable Auto answer with headset on DN but still any incoming call on phone not auto answer, is there anything I miss other than configure auto an...

Delink router configuration

I tried to connect my new delink router from other primary delink router for WIFI only. Can someone explain step by step for configuration

Redistribute routes on ABR router having Area0 and Area 13

Rtr1 ----Cost1-----> Rtr2 (Area13)Rtr1 ----Cost1-----> Rtr3 (Area13)Rtr2 ----Cost10----> Rtr3 (Area10)Rtr2 ----Cost10----> Rtr4 (Area0) If i redistribute static route on Rtr2 then Rtr3 learns best route from Rtr1If i redistribute static route on Rtr4...

AP Status joined but obb error image download

My ap Is joined but l got errors with obb AP-model ap-air2802i-b-k9 wireless controller 9800-CL 17.9.4 [*04/20/2024 19:08:59.6159] Discovery Request sent to 192.168.178.150, discovery type STATIC_CONFIG(1)[*04/20/2024 19:08:59.6432] Discovery Reques...

Problem with AP configuration cisco CBW150AX. I can't connect to netwo

I have a secret problem with starting Cisco Access Point: CBW150AX-E-EU.When I connect it directly to the Cisco ASA 5506x, the AP does not want to connect at all. It means it doesn't get the address from DHCP. DHCP allocates a windows server. When I ...

IPv4 DIA & IPv6 DIA - over the same transport interface

Hello , We would run dual stack (IPv4 & IPv6) at service side, and also we would run dual stack (IPv4 & IPv6) on the transport internet interface(underlay), on SD-WAN router. Is it possible to enable IPv4DIA (NAT44) and IPv6 DIA (NAT66) via the same...

Disable PPTP and L2TP server

Hello!I tested PPTP and L2TP VPN solutions, but considered another solution without the Cisco router involved.I've disabled all the virtual-access and vpdn stuff,sh run all | i vpdnreturns nothing, but the ports for PPTP and L2TP are still open and c...

Uccx with sip

I have script with toll free number(sip) the caller sometimes hear all audio prompts in menu, and sometime hear some audio prompts which not stable, but when I dial internally the trigger it is stable and I can hear all audio prompts in menu, What co...

No Signal - codec awake but no video output until rebooted

Equipment: Webex Room Bar (on prem) connected to single 65" screen LG UHD Commercial DisplayIssue: "No Signal" showing on screen. Correct source selected (confirmed as the LG screen names the source as Cisco Codec and when the codec was rebooted i...

Multicast Lab Auto-RP

Hi ALL,I have setup a lab in CML for testing multicast using Auto-RP but I cant see traffic flowing from the source to the receivers . I can see the (S,G) entry in the first hop router and the (*,G) entry in the RP .Appreciate any feedback Thanks,Fra...

To enter name of the person via speech instead of dialing by name

I have UCCX 12.5 ,CUCM 12.5 and imp 12.5 in my lab.I have Auto Attendant Script deployed. I love the script but i need something better.I would like the customer to speak the name of the person instead of dialing the name can the Auto Attendant scrip...

Upcoming Event: Capture the Flag, get the Badge!

You asked, we heard you! Introducing the ThousandEyes Support Community Capture the Flag event from April 23rd at 8 AM PST to April 29th at 5 PM PST. This month the ThousandEyes Community is offering two Capture the Flag missions in a single upcoming...

Setting UP a SECOND ASA5506-x firewall

Hello, I successfully set up/configured my first ASA device. I just purchased as second 5506 and am wondering about how compatible or incompatible the bkup configuration files I’ve saved from the first device are gonna be with the second ASA. It ment...

Technology and Support

Browse the Community

Certified Remanufactured Equipment

Cisco Software

Cisco Start

Collaboration

DevNet Hub

Data Center and Cloud

Internet of Things (IoT)

Networking

Online Tools and Resources

Security

Service Providers

Services

Small Business Support Community

Wireless - Mobility